AC Repair in Newark, OH: How to Repair 3 Common Issues

There can be a couple of explanations why your air conditioning won’t run: a triggered circuit breaker, inaccurate thermostat settings, a switched off switch or a full condensate drain pan.

Your air conditioning won’t start when you have an overloaded breaker.

To see if one has gotten overloaded, go to your residence’s main electrical panel. You can spot this metallic device on the wall in the basement, garage or closet.

• Confirm your hands and feet aren’t wet before you work on the panel or breakers.
• Look for the breaker identified “AC” and make sure it’s in the “on” position. If it’s triggered the lever will be in the middle of the panel or “off” position.
• Firmly shift the breaker back to the “on” location. If it instantaneously trips again, don’t reset it and contact us at 740-344-5497. A fuse that keeps flipping might mean your house has electrical trouble.

If your thermostat isn’t giving a sign to your air conditioner to start, it won’t activate.

The main part is checking it’s switched to “cool” and not “heat.” Otherwise your air conditioning might not turn on. Or you might receive. warm air blowing from vents being the heat is on instead.

If you’re using a regular thermostat:

• Swap out the batteries if the monitor is blank. If the monitor is presenting jumbled letters, buy a new thermostat.
• Ensure the proper mode is displaying. If you can’t update it, override it by dropping the temperature and pushing the “hold” button. This will make your AC start if programming is not right.
• Attempt to set the thermostat 5 degrees below the house’s temperature. Your AC won’t work if the thermostat is set the same as the room’s temperature.

Once your thermostat is adjusted properly, you should begin getting cool air fast.

If you’re using a smart thermostat, including ones manufactured by Nest, Ecobee, Lux, Honeywell or Bosch, look at the manufacturer’s website for troubleshooting. If it still won’t work, contact us at 740-344-5497 for assistance.

Your AC probably has a shut-off lever around its condenser. This device is commonly in a metal box hung on your house. If your unit has recently been maintained, the switch may have accidentally been put in the “off” position.

Condensate drain pans keep the surplus water your equipment removes from the air. This pan can be found either beneath or within your furnace or air handler.

When there’s a blockage or blocked drain, water can build up and prompt a safety setting to stop your air conditioner.

If your pan includes a PVC pipe or drain, you can drain the additional water with a formulated pan-cleaning capsule. You can buy these tablets at a home improvement or hardware store.

If your pan involves a pump, find the float switch. If the switch is “up” and there’s liquid in the pan, you might have to replace the pump. Contact us at 740-344-5497 for support.

If your air conditioner is going but not providing cold air, its airflow might be clogged. Or it may not have sufficient refrigerant.

Your unit’s airflow can be limited by a plugged air filter or dirty condenser.

A dirty filter can create countless issues, including:

• Reduced comfort
• Icy refrigerant lines or evaporator coil
• Intermittent cooling
• Increased utility expenses
• Causing your system to stop working sooner

We recommend installing new flat filters once a month, and accordion filters every three months.

If you can’t recall when you last installed a new one, shut off your AC completely and remove the filter. You can find the filter in your furnace or air pump’s blower compartment. It could also be located in an adjoining filter holder or wall-mounted return air grille.

Angle the filter up to the sunshine. If you can’t see any light you should get a new one.

Weeds, grass and bushes can block your condensing equipment. This may limit its airflow, impact its energy efficiency and affect your comfort. Here’s a method you can follow to get your unit running smoothly again.

1. Shut off electricity fully at the breaker or outside device.
2. Remove plant rubbish around the unit. Once you’ve gotten rid of larger refuse within a two-foot radius, you can use a paint brush or vacuum to carefully remove dirt from the unit’s fins. Bent fins can also affect performance, so you can attempt to correct them with a small knife.
3. Use a hose nozzle to slowly remove gunk off the fins from inside the system. Be careful to avoid getting liquid on the fan motor.
4. Replace the top and turn on the power.

When cooling systems don’t have sufficient refrigerant, they’ll have difficulty removing heat and humidity from your home.

Here are several symptoms that your system is seeping refrigerant:

1. It takes an extended amount of time to lower the temperature in your residence and you’re regularly decreasing the temperature on the thermostat.
2. Air coming through the registers isn’t as cold as it should be.
3. You’re hearing fizzing or bubbling noises when the AC is on.
4. Your evaporator coil is iced over as a result of having difficulty taking on humidity.

Think your equipment is seeping refrigerant? You need a authorized heating and cooling service specialist to take care of the leak and replenish the right level of refrigerant in your equipment. Reach us at 740-344-5497 for assistance.

When it seems like you’re not receiving adequate amounts of chilled air, there’s possibly an obstruction or separation inside your cooling system.

• The beginning stage is checking your air filter. Get a new one if it’s soiled.
• Then make sure the vents are clear around your home.
• If you’re still not receiving adequate cold air, you should have your ducts inspected by a professional like Luikart Heating & Cooling. Your ducts might need to be serviced or hooked up again in difficult locations like your attic, basement or crawl space.